Wednesday, May 22nd 2013, 5:04am UTC+2

You are not logged in.

  • Login
  • Register

unable to halt ARM core

Dear visitor, welcome to SEGGER Forum. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

fevernova

Beginner

Date of registration: Jan 28th 2008

Posts: 2

1

Monday, January 28th 2008, 1:12pm

unable to halt ARM core

Hi at all,


I designed a my own Cirrus ARM 9307 board. Now I started with commissioning. I started J-Link Commander (V3.78d).


The message is :


"Info: TotalIRLen=4, IRPrint = 0x01"


"JTAG Speed: 29kHz"


"Info: Using DBGRQ to halt CPU"


"Resetting TRST in order to halt CPU"


"Info: CP15.0.0, 0x41129200, ARM, architecture 4T"

"Error: unable to halt ARM core"

"Trying to connect with 5kHz!"

It's also not possible to debug a blinky in IAR IDE. X(

HW-Info

MikeQ

Beginner

Date of registration: Dec 3rd 2007

Posts: 16

2

Monday, January 28th 2008, 9:14pm

Obviously J-Link can "talk" to your chip.
The problem is that it can not halt the chip for some reason.
Most likely cause is that the target CPU has no clock or that
it is performing a memory access which halts the CPU indefinetly.

Can you
a) Check if the CPU has a clock
b) Check if there is a "WAit" Signal which may be active

If this does not help, try "rx 0" from J-Link Commander as follows:

SEGGER J-Link Commander V3.78a ('?' for help)
Compiled Dec 4 2007 22:18:44
DLL version V3.78a, compiled Dec 4 2007 22:18:35
Firmware: J-Link compiled Dec 03 2007 17:15:31 ARM Rev.5
Hardware: V5.30
S/N : 1
Feature(s) : RDI, FlashBP, FlashDL, JFlash, GDB
VTarget = 3.306V
Info: TotalIRLen = 4, IRPrint = 0x01
JTAG speed: 30 kHz
Found 1 JTAG device, Total IRLen = 4:
Id of device #0: 0x3F0F0F0F
Found ARM with core Id 0x3F0F0F0F (ARM7)
J-Link>speed 2000
JTAG speed: 2000 kHz
J-Link>rx 0
Reset delay: 0 ms
Reset type NORMAL: Using RESET pin, halting CPU after Reset
Info: TotalIRLen = 4, IRPrint = 0x01
Info: Resetting target using RESET pin
J-Link>

Does this help ?

fevernova

Beginner

Date of registration: Jan 28th 2008

Posts: 2

3

Thursday, January 31st 2008, 8:16am

Now it works, /wait was active.

Thanks a lot.

pankaj.pandey

Beginner

Date of registration: Mar 10th 2008

Posts: 2

4

Monday, March 10th 2008, 2:49pm

Can u tell me how to check whether nWait is active or not?

I checked my Datasheet for AT91SAM7x256 ,there is no signal as nWait.

kindly reply.

spy1

Beginner

Date of registration: Mar 10th 2008

Posts: 10

5

Thursday, July 24th 2008, 6:33pm

I have a question

I am using the flasher for ARM... and J-Link commander detects my microcontroller (Cortex - M3). When I try to erase the flash, I got an error (CPU is not halted).

- ERROR: CPU is not halted
- ERROR: Timeout while checking target RAM, core does not stop
- ERROR: Failed to erase sectors

On our circuit, we didn't connect pin 15 to the reset pin of microcontroller. Is it a problem? Our reset is connected to a R-C circuit.

Also, I tried to use the flasher as a standalone... and when I press the Start/Stop button, I don't see any programming action...



I'd like to get an answer about there issues.



Regards



Christian

Similar threads